Intergraph PV Elite 2019 version 21.0.0
Intergraph PV Elite 2019 version 21.0.0 | 507.4 mb
CADWorx & Analysis Solutions is pleased to announce the availability of Intergraph PV Elite 2019 version 21.00.00.0000. the newest version of its complete solution for vessel and heat exchanger design, analysis and evaluation used by engineers, designers, estimators, fabricators and inspectors.
Code Updates
- Updated to support IBC 2018wind & seismic code.(RI-TX-24759)
- Updated to support Mexican MDOC 2015seismic code.(RI-TX-22221)
- Updated to support PD 5500:2018+A1code update.(RI-TX-24841)
- Updated to support KHK 2012seismic code.(RI-TX-1443)
- Updated to support Type 2 Jacketsfor PD 5500 & EN 13445.(RI-TX-23191)
Configuration
- Updated PV Elite to allow the option to make the external length L for cylinders connected to weld neck flanges.(CR-TX-26285)
- Updated PV Elite to allow users in Europe to enter through the keyboard a decimal comma instead of the decimal point in the input. The software should convert the comma to a period automatically.(CR-TX-27346)
- Normally MDMT's are computed using hoop stress because hoop is twice longitudinal. But in a low-pressurecolumn with high bending stress longitudinal might govern.(CR-TX-28335)
Input Processor & Analysis
- Updated PV Elite to show the help topics through a WPF help .NET desktop application. WPF help is designed to be a modern, easy-to-use help application that can run from any folder without formal installation.(CR-TX-24837)
- Updated PV Elite to allow long description names for nozzles so that users can keep description names of longer than 16-characternames.(CR-TX-25730)
- Updated PV Elite to consider table UHX-8.1 of ASME Sec VIII Div 1 to determine W* value used in tubesheet calculations and consider full bolt load W*=Sa*Ab, in the tubesheet calculation.(CR-TX-25353)
- Updated PV Elite to add a checkbox to allow the option to make the external length L for cylinders connected to weld neck flanges include the Flange overall length.(CR-TX-26285)
- Updated PV Elite to add a "service type" and "Radiography" input field in case of a heat exchanger component, so it that will be useful to apply different minimum thickness as per UG-16(b) as per service for shell side, as well as tube side and will comply Code requirements.(RI-TX-21488)
- Updated PV Elite to include an option to enter allowable shear stress for anchor bolts based on ASD, Steel Construction Manual, not ASME Sec II, for shear stress analysis.(CR-TX-12919)
- Updated PV Elite to add bolting data for 3P metric bolting designs. Bolt data is per Table H-1 of ASME PCC-1.(CR-TX-24815)
- Updated PVElite to show the fabricated section ring on the inside or outside of the vessel as specified.(CR-TX-15558)
- Updated PV Elite to allow the user to specify that the Pressure (Design) only cases are to be used to compute the MAWP for hydrotest for ASME heat exchangers.(CR-TX-26654)
- Updated PV Elite to add a check box that allows the user to force the VIII-1, 1-5 calculation to happen when delta is greater than alpha, and the cone is connected to a flange. (CR-TX-27162)
- Updated PV Elite to set the allowable for Pm+Pl+Q to be changed to 3*Sh if there are no thermal expansion loads provided, also the user can specify a cyclic temperature to calculate the allowable for Pm+Pl+Q stress based on the rules of ASME VIII-2 Part 4,4.1.6.3 (a) and (b). (CR-TX-26685)Output Processor & Reports
- Updated PV Elite to show all the data points in both Point Thickness Readings and Critical Thickness Profiles in the output report to verify that they are correct without having to go back to the input file.(CR-TX-4668)
- Updated PV Elite to show the total wind deflection that includes user defined forces, so that users do not have to add them together by hand. A line will be included after the deflection stating, "Total deflection, including wind and user applied forces". A user force must be specified. (CR-TX-25243)
- Updated PV Elite to support and show UW-16.1 sketches v-1 through w-2, so that users can see the weld representations in the nozzle calculation report.(CR-TX-26306)
- Updated PV Elite to add a note to show that ambient temperature is used instead of design temperature for WRC 107/ 537 in the Lifting Lug calculation report.(CR-TX-26267)
- Updated PV Elite to report correctly the lifting lug placement detail for horizontal vessels. Currently, lifting lug report for horizontal vessels shows as "Design reaction force at the tailing lug". It must be Left or Right lug.(CR-TX-26242)
- Updated PV Elite to see the title of the weight type in the Element and Detail Weights report so that it can more easily identify where the weights are coming from.(CR-TX-26592)
- Updated PV Elite to clean up printout for Electric Immersion Heaters in the Internal Pressure Calculations report while running a PED hydrostatic test.(CR-TX-26656)
- Updated PV Elite to suppress a Flange governing being flagged in the Failures Summary and only show the warning during the analysis run time iteration.(CR-TX-26607)
- Updated the API 579 report to show all the data points in the output to verify that they are correct without having to go back to the input file.(CR-TX-26254)
- Updated the WRC 297 allowable stress for Pm+Pl+Q to 3*S (which is taken from ASME section VIII, Division 2), shown in the Vessel Stress Summation Comparison table stress.(CR-TX-10228)
About PV Elite. This pressure vessel and heat exchanger design software is easy to learn and use. PV Elite gives users fast start-up and confidence in their safety code calculations.
PV Elite provides engineers, designers, estimators, fabricators and inspectors with solutions that match their pressure vessel and heat exchanger design needs. Because the program is easy to learn and use, it is perfect for both regular and occasional users requiring fast start up and confidence in their safety code calculations.
PV Elite is a complete solution for the quick and intuitive design of new pressure vessels, and it also evaluates and re-rates existing vessels, including Fitness for Service analysis. The program considers the whole vessel, addressing all of the wall thickness rules and stress analysis requirements for vertical towers, horizontal vessels and heat exchangers.
About CADWorx & Analysis Solutions. For more than 25 years, CADWorx & Analysis Solutions has provided software for multiple plant design and engineering disciplines. Our aim is that design and engineering should share relevant information seamlessly, thereby maintaining accuracy and improving efficiency.
Our offerings conform to that goal and include: CADWorx Plant Design Suite for intelligent plant design modeling, process schematics and automatic production of plant design deliverables; CAESAR II, the world's most widely used pipe stress analysis software; PV Elite for pressure vessel and heat exchanger design and analysis; TANK for the design and analysis of oil storage tanks, and GT STRUDL for structural analysis and design modeling.
Our products are used around the world by nearly every major Owner Operator and global EPC firm. Likewise, thousands of mid to small size companies are benefiting from the powerful, yet scalable, solutions that we develop. If you have work to do, correctly, on time, and under budget, you too should be looking at our offerings.
Product: Intergraph PV Elite
Version: 2019 version 21.00.00.0000
Supported Architectures: x64
Website Home Page :
http://www.coade.comLanguage: english
System Requirements: PC
Supported Operating Systems: *
Size: 507.4 mb
Windows 7/8/8.1 Professional (64 bit)
Windows 7/8/8.1 Ultimate (64 bit)
Windows 7/8/8.1/10 Enterprise (64 bit)
Windows 10 Pro (64 bit)
Windows Server (all versions)
DOWNLOAD LINKS :
https://rapidgator.net/file/295bf0f6abc355e7df4dbe576ae14ac8/r5gq7.Intergraph.PV.Elite.2019.version.21.0.0.rar.html
http://nitroflare.com/view/D9AFF2099B64FA6/r5gq7.Intergraph.PV.Elite.2019.version.21.0.0.rar
https://ayefiles.com/da3c7u8ewmgb/r5gq7.Intergraph.PV.Elite.2019.version.21.0.0.rar.html
https://turbo.to/8navep31swvu/r5gq7.Intergraph.PV.Elite.2019.version.21.0.0.rar.html
Cantinho Satkeys
